The Kitchen STL Pack: 5 Original 3D Print Files — Stands, Holders, Hooks & Clips | Fast, Cheap & Confident

The little kitchen helpers are never in the drawer when you need them. Print your own.

The Kitchen STL Pack is five original 3D print files for the dry, organizational side of a working kitchen — the stands, holders, hooks, and clips that keep a cookbook open, a recipe card upright, a spoon off the stove, a bag hanging open, and a pantry shelf labeled. No measuring cups, no food-prep surfaces, nothing that touches food. Every design is thick-walled (nothing under 2.5 mm), flat-based, needs no supports, and fits a standard home printer bed — nothing is bigger than 140 mm in any direction.

The five files:

- Recipe Card & Tablet Stand (140 × 100 × 76 mm) — an easel stand with a low front lip and a leaning back panel. Tablets, phones, and recipe cards sit in the ~32 mm channel and stay put when you tap the screen.

- Cookbook Page Holder (130 × 26 × 13 mm) — a low gutter wedge that rests in the center fold of an open cookbook and helps the pages lie open at the recipe you're cooking.

- Spoon Rest (115 × 78 × 12 mm) — a shallow tray with a 9 mm-deep well for the stirring spoon or spatula between stirs. Utensils only — see the honest notes.

- Cabinet-Door Bag Hook (40 × 31 × 60 mm) — drops over a standard ~19 mm (3/4") cabinet door; the outside ledge holds a grocery bag open for trash or peelings. Print two for a pair.

- Pantry Label Clip (60 × 22 × 30 mm) — slides onto 16–18 mm shelf edges; the flat front plate takes a paper label or label-maker strip. Print a set of six to ten and label the whole pantry.

Plus the Print & Settings Guide (PDF, 10 pages): one page per piece with a rendered preview, the exact orientation (two pieces print in a specific direction on purpose — the guide says why), layer height, walls, infill, material pick, support notes, fit and scaling notes, and a quick-fixes table. Every file passed a software check as a single watertight solid before it went in this pack — the same check your slicer runs.

Honest notes (please read — this is the fine print, in normal size):

- Home-printed plastic is not certified food-safe. FDM layer lines can harbor bacteria, and filament isn't a food-contact material. That's exactly why every design here is a stand, holder, hook, or clip — no measuring cups, no prep surfaces, no food storage. The spoon rest holds utensils between stirs; wash it like a utensil rest, keep it off direct heat, and don't store food in it.

- These files were designed and geometry-verified, not test-printed on every printer. Your printer, filament, and settings are yours. The two fitted pieces (door hook, shelf clip) may need a test print and a percent or two of scaling — the guide walks you through it, and the smallest clip is the built-in test piece.

- Original designs — and what they're not. All five designs are original to this pack, drawn in 2026. They are not the files behind my printed-and-shipped products, and this pack does not include those designs.

- No printer? My printed pieces are made and shipped by Slant 3D Portals: the Cookbook Stand ($29.99) and the Spice Packet Organizer ($39.99) — different designs, zero printing on your end.

- You need a 3D printer (or access to one) and a slicer. This is a set of STL files plus a PDF guide — no physical product is shipped.

License (in plain words): Print the files for yourself as often as you like. You may sell the printed pieces — markets, your own shop, your neighbors. You may NOT resell, share, give away, or upload the STL files themselves. One purchase covers one household or one small business's printer.

Where it sits on my shelf: my Portals pieces are printed for you ($29.99 / $39.99, shipped). This pack is printed by you — five different, original designs at $18, priced below a single printed piece because your printer and filament do the making. The Asset Library Kit ($27) is the filing system for shops that make files like these; this pack is files to make. Each is sold separately.

Details: 5 STL files (millimeters, watertight-checked) + Print & Settings Guide PDF (10 pages). Largest piece 140 mm — fits standard home printer beds (150 mm and up). Materials: PLA for everything; PETG recommended for the spoon rest. Price: $18 one-time. By Jerry Madrigal — Fast, Cheap & Confident, San Antonio, TX. Everything in one place: https://linktr.ee/jerrymad123