Motortier SMG - A full-auto, shell-ejecting, nerf-compatible blaster - v1.7 - TO ORDER

The Motortier SMG is another blaster in a cyber-future where german trains run on time, no matter what. Train guards are equipped with it by default, if they don't opt for a Rail Cleaner instead. According to them they appreciate the ability to "rapidly switch between targets" with one quick spray across the room. 

Train conductors are less thrilled by the shell-sweep afterwards, but they do appreciate the added security these blasters provide nontheless. The casualty rate of passengers and staff on trains has been reduced by 16% on average since its introduction in 2388. It formally replaced the short-barreled and woefully outdated Morgenstern MKII as a primary.

Technically speaking, this is a Nerf-compatible flywheel blaster that uses Flypoint-compatible shells. It fires half-darts in full-auto at rapid speed. The blaster has a separate rev-trigger that is attached to the front of the firing trigger, for a controllable dual-stage trigger feeling. The Flypoint shells are made by GDop26, whose work you can check out at shellingtonblasters.com

The blaster is powered by a 3S LiPo. The battery is not included. You'll need to have your own 3S LiPo that can take at least 60A stall current. The LiPo goes into a compartment in the front of the blaster, for balance reasons. Inserted into the top of the blaster is a voltage meter, to plug your LiPo into. The magazines hold by default 30 shells each, in a double-stack configuration. I also offer shorter 15 shell mags, if you want it to be compact. 

It fires about 20 meter in a straight line, and 30 meter at an angle. By default the Motortier SMG comes with 3S OoD Lokis for motors, embedded in a Stryfe-compatible cage and flywheel combo for maximum compatibility. They'll give you roughly 140 FPS on average, I hear. On the front is an N-Strike-compatible barrel lug.

---

Together with the blaster you'll also receive 2x 30-shell magazines, 1x 15-shell magazine, 100 Flypoint-compatible half-darf shells, 2 storage boxes that can each hold 50 shells, and 1 talon magazine adapter.

I'll ask you what color you want those in when you purchase this listing.

There are no single or burst fire options. The blaster is an uncivilized brute, only intent on shows of glowy power and spraying shells.

---

The blaster is made TO ORDER, which means that I will make it in the colors of your chosing, specifically for you. My opening message after purchase will be to ask you about the color scheme. By default the blaster has a Primary, Secondary, and Transparent Color (+ Black for the grip).

The creation process typically takes roughly 3 weeks, give or take.

I will keep you updated during the entire process at every step.

Lastly: Contact me if you need a left-handed version. I can create a custom mirrored blaster for you.

---

KNOWN REVIEWS

WalcomS7 -> https://www.youtube.com/watch?v=GigijwxnTVE

DrFlux -> https://www.youtube.com/watch?v=1xbxZ3za2KM

Boomstick Mods -> https://www.youtube.com/watch?v=48LnFMSSg1w

---

Changelog:

v1.6

- Changed the shell extractor geometry so the cap can be printed in a different orientation. That should improve its overall sturdiness.

- Changed the gear system, mag release and lipo compartment to not use 4mm aluminium rods anymore. That removes the need for 4mm rods entirely. It should be easier to get the hardware together now.

- Reinforced the bottom frame that grips around the magazine. If the blaster fell down beforehand in an unfortunate way then the magazine could lever the blaster in half. This will ideally prevent that.

- Changed the motor gear from using a heat insert to using a captive M3 square nut. Heat inserts annoy me.

v1.7

- Modified the magazines to have more useful/consistent screw ports. This is mostly just an act of rolling up some legacy issues.

- The default model now also comes with a small 15 dart magazine, for a total of 3 mags with every purchase. I want people to use these more. They're neat.